Mitsubishi Diamond Plus 92 Especificaciones

DDCcontrol DocumentationNicolas Boichat

Usage6

Appendix A. Report problems andsuccessesIf you have problems building or running DDCcontrol, if your monitor doesn't work with DDCcon-trol, or if

Appendix B. Supported monitorsThe following monitors are supported by DDCcontrol:Dell• Dell 1704FPT (DVI input)Fujitsu Siemens• P17-2• P19-2• P20-2 (V

• SyncMaster 712N (at least VGA input)• SyncMaster 912N (at least VGA input)• SyncMaster 930BF (at least VGA input)• SyncMaster 997MBYour monitor is n

Appendix C. Supported graphicscards/dev/i2c-* versus PCI memoryTo control a monitor, DDCcontrol must access to the I2C bus of the graphics card. There

NameWorksdev PCIRadeon 9200 Yes ???Radeon 9500 Yes ???Radeon 9550 SE Yes ???Radeon 9600 Pro Yes ???Radeon 9700 Yes ???Radeon 9800 Pro Yes YesnVidiaDir

NameWorksdev PCIGeForce FX 5600 No YesGeForce FX 5700 No YesGeForce FX 5700 LE ??? YesGeForce FX 5950 Ultra ??? YesGeForce 6200 TC ??? YesGeForce 6800

Matrox cards support tableThese Matrox cards have been reported to work. If yours is not listed, please send a message to oneof the DDCcontrol mailing

Appendix D. ThanksThanks to Oleg I. Vdovikin, for his work which was used as a basis for ddccontrol, and for his helpwhen designing the XML database.T

Appendix E. Documents fordevelopersMonitor database structureThe monitor database is written in XML, it can be found in the db directory of ddccontrol

DDCcontrol DocumentationNicolas BoichatCopyright © 2005 Nicolas BoichatDocumentation for DDCcontrol version 0.3.

• “command”: An action occurs when the value is set to something greater than “0” (e.g.degauss). If you don't define any value element in a comma

following:• If caps is not defined, caps are read from monitor.• If this attribute exists and have a “vcp” string (e.g. “type(lcd) vcp(10 12)”) then t

<profile pnpid="%pnp_id%" name="%profile_name%" version="1"><control address="%hex_address%" value=&q

Appendix F. GNU General PublicLicenseVersion 2, June 1991Copyright © 1989, 1991 Free Software Foundation, Inc.Free Software Foundation, Inc.59 Temple

everyone's free use or not licensed at all.The precise terms and conditions for copying, distribution and modification follow.TERMS AND CONDITION

not derived from the Program, and can be reasonably considered independent and separate works inthemselves, then this License, and its terms, do not a

prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Pro-gram (or any work based on the Program), you indi

If you wish to incorporate parts of the Program into other free programs whose distribution condi-tions are different, write to the author to ask for

If the program is interactive, make it output a short notice like this when it starts in an interactivemode:Gnomovision version 69, Copyright (C) year

Table of Contents1. About DDCcontrol ... 1About DDCcontrol .

Chapter 1. About DDCcontrolAbout DDCcontrolDDCcontrol is a tool used to control monitor parameters, like brightness and contrast, without usingthe OSD

Chapter 2. Install notesSoftware RequirementTo compile and run DDCcontrol, you need to have these packages installed:• libxml2 [http://www.xmlsoft.org

If your graphics card is supported by /dev/i2c-* devices (see Appendix C, Supported graphicscards), you must load the i2c-dev module by typing, as roo

Chapter 3. UsageGTK+ GUIIf GTK+>=2.4 is installed on your computer, the configure process will detect it, and build theGTK+ application.The GTK+ GU

Device : pci:01:00.0-2Detected monitors :- Device : pci:01:00.0-1DDC/CI supported : YesMonitor Name : Samsung SyncMaster 173P (DVI)Input type : Digita