Mitsubishi 930 Manual de instalación

Graphic Operation Ter minalsHuman-Machine-InterfaceInstallation ManualF920GOT-BBD5-K-EF930GOT-BBD-K-EINDUSTRIAL AUTOMATIONMITSUBISHI ELECTRICArt.-Nr.:

2.3 Dimensions and Panel-cutoutSpecifications10 MITSUBISHI ELECTRICAll dimensions in mm921061347F1F2F3 F4F5F64108952-63.ESCENTSETDEV535,511811990COM0

3 Description of the GOTs3.1 F920GOT-BBD5-K-EDescription of the GOTsF920GOT-K / F930GOT-K 117F1F2F3F4F5F64108952-63.ESCENTSETDEVCOM0 RS-422 COM1 RS-23

3.2 F930GOT-BBD-K-EDescription of the GOTs12 MITSUBISHI ELECTRICNumber Item Description쐃 DisplayMonochrome liquid cristal display (LCD) with touch-sen

3.2.1 Labeling the Function KeysThe function keys of the F930GOT-K can be labeled to suit the application. Insert the label fromthe rear of the GOT:3.

4 InstallationThe operation terminals of the GOT F900 series are designed to be mounted in a control panelor the door of a control cabinet.All mountin

4.2 MountingThe GOT is fixed in the panel with the mounting brackets (four for the F920GOT-K, six for theF930GOT-K) delivered with the operation panel

5 Wiring5.1 Connection with the PLC5.1.1 F920GOT-BBD5-K-EECAUTION:Do not connect a PLC to the RS422 port and at the same time a second PLC to theRS232

Connection to a CPU of the MELSEC System QThe RS232C port of the GOT is used to connect a F920GOT-K with the programming port of a Qseries CPU:When a

5.1.2 F930GOT-BBD-K-EConnection to a CPU of the FX0, FX0S,FX0N,FX1S,FX1N,FX2N or FX2NC series, or theinterface adapters FX1N-422-BD and FX2N-422-BD:Co

Connection to the programming port of a A or QnA series CPUConnection to the interface modules AJ71UC24, AJ71QC24N, A1SJ71UC24-R4,A1SJ71QC24, and QJ71

About this ManualThe texts, illustrations, diagrams, and examples contained in this manualare intended exclusively as support material for the explana

Connection to the interface modules AJ71C21-S1, AJ71UC24, AJ71UC24-S2,AJ71QC24N-R2, and AJ71QC24NConnection to the interface modules A1SJ71UC24-R2, A1

5.2 Connection to a Personal ComputerFor the transfer of the user screens to the operation terminal, connect a PC or a notebook com-puter (with the re

6StartUp햲Make all connection required as shown in chapter 5.햳Turn on the power of the GOT.햴Check the display. On the system screen „SET-UP MODE“ you c

7 MaintenancePDANGER:Always switch off the power supply of the GOT before starting the replacement of thebattery.7.1 Replacement of the battery (F930G

MITSUBISHI ELECTRICINDUSTRIAL AUTOMATIONMITSUBISHI ELECTRICGothaer Straße 8 Telefon: 02102 486-0 Fax: 02102 486-7170 www.mitsubishi-aut

F920GOT-K / F930GOT-K 31 Introduction1.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety InformationFor qualified staff onlyThis manual is only intended for use by properly trained and qualified electrical technicians whoare fully a

Safety warnings in this manualIn this manual special warnings that are important for the proper and safe use of the products areclearly identified as

General safety information and precautionsThe following safety precautions are intended as a general guideline for using the PLC togetherwith other eq

1 IntroductionThis Installation Manual includes a brief summary of the main specifications of the graphic oper-ation terminals F920GOT-BBD5-K-E and F9

2 Specifications2.1 General SpecificationsECAUTION:Please operate the Graphic Operation Terminal in the listed conditions only.If the GOT is used unde

2.2 Specifications of the Operating TerminalsSpecificationsF920GOT-K / F930GOT-K 9Item F920GOT-BBD5-K-E F930GOT-BBD-K-ESupply voltage5 V DC (±5%)(supp