Mitsubishi Q62DAN Manual de usuario descargar pdf (Pagina 59)

2 - 26 2 - 26

MELSEC-Q

2 INPUT MODULE SPECIFICATIONS

2.20 QX80H DC High-speed Input Module (Negative Common Type)

DC high-speed input module (Negative Common Type) Type

Specifications

QX80H Appearance

Number of input points 16 points

Isolation method Photocoupler

Rated input voltage 24VDC (+20/-15%, ripple ratio within 5%)

Rated input current Approx. 6mA

Input derating Refer to the derating chart.

ON voltage/ON current 13V or higer/3mA or higher

OFF voltage/OFF current 8V or lower/1.6mA or lower

Input impedance Approx. 3.9k

SW1 (noise

filter)

OFF ON

Set value 2 Invalid 0.1 0.2 0.4 0.6 1

TYP. 0ms 3 0.04ms 0.10ms 0.25ms 0.50ms 0.95ms

OFF to ON

MAX. -

3 0.05ms 0.15ms 0.30ms 0.60ms 1.00ms

TYP. 0ms 3 0.04ms 0.10ms 0.25ms 0.50ms 0.95ms

Response

time

ON to OFF

MAX. -

3 0.05ms 0.15ms 0.30ms 0.60ms 1.00ms

Function

setting

SW2

4 OFF: Interrupt, ON: High-speed input

Dielectric withstand voltage 560VAC rms/3 cycles (altitude 2000m (6557.38ft.))

Insulation resistance 10M or more by insulation resistance tester

Noise immunity 5

By noise simulator of 500Vp-p noise voltage, 1

s noise width

and 25 to 60Hz noise frequency

Protection of degree IP2X

Common terminal

arrangement

8 points/common (common terminal: TB9,TB18)

Number of I/O points

16 (I/O allocation is set as a 16-points high-speed input module or interrupt

module)

Interrupt processing condition Set by Switch setting in GX Developer 4 6

Operation indicator ON indication (LED)

External connections 18-point terminal block (M3 6 screws)

Applicable wire size 0.3 to 0.75mm

core (2.8mm (0.11in.)OD max.)

Applicable crimping terminal R1.25-3 (sleeved solderless terminals cannot be used.)

5VDC internal current

consumption

80mA (TYP. all points ON)

Weight 0.16kg

1: If turning on the switch 1, the noise filter takes effect.

The off-status noise filter disables I/O response time setting.

After switching on or off the switch 1, reset the power supply of the CPU module.

2: Set an input response time in

I/O response time

combo box of PLC parameter in GX Developer. (Default: 0.2ms)

The response time in SW6D5C-GPPW or later can be changed.

For the setting details, refer to Section 1.3.1.

3: The actual response time is 5 s delay when turning on, 10 s delay when turning off, because the hardware response time is added.

For the details of the CPU overhead time, refer to manuals for the CPU module used (Function Explanation, Program Fundamentals)...

4: The module function can be changed according to the switch 2 status.

ON : High-speed input

OFF : Interrupt

If changing the switch 2 setting while the CPU module is in RUN, an error (error code:2100) occurs.

5: Indicates the noise immunity when the noise filter takes effect (the switch is turned on).

6: For the setting method, refer to Section 1.3.3.

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 143 144

Comentarios a estos manuales

Sin comentarios

Mitsubishi Q62DAN Manual de usuario Pagina 59

Comentarios a estos manuales

Relacionado con productos y manuales para Los Componentes Del Dispositivo De Seguridad Mitsubishi Q62DAN